1998 Nissan 240SX SE

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/DSC_4215.jpg
As it sits as of 2010

http://i80.photobucket.com/albums/j175/blackice00/random/2fa8f3780-1.jpg


My car was originally automatic, has no abs, but has a sunroof and is 5 lug. When I bought it, it was already swapped to 5 speed with the VIS Omega front bumper. The stock KA24de ended up blowing a headgasket on me after a series of water pump issues.

Engine/Performance:

Stock Replacement Parts:
Nissan oem waterpump
Nissan oem thermostat
Nissan Sentra SE-R oil filter
Nissan 300zx TT fuel filter
NGK BKR7ES11 spark plugs
new serpentine belts
valve cover studs and nuts

Engine/Tranny:
1995 200SX S14 (Zenki) SR20det
Mishimoto starter
5 speed transmission
steel braided clutch line

Intake:
K&N V-Flow Dry Filter
APEX'i 507-N021 Racing Suction Kit with z32 MAF
Greddy hot pipe
Greddy V-SPL front mount intercooler
Greddy RZ Limited Edition blow off valve

Exhaust:
Greddy O2 housing/turbo elbow
Greddy 3" downpipe
Blitz Nur-SpecR Exhaust (80mm piping, 114.3mm tail pipe)

Fueling:
Nismo 555cc injectors
Bosch 040 in-tank fuel pump
adjustable fuel pressure regulator

Cooling/turbo
HKS adjustable wastegate actuator
DIF top mount turbo coolant and oil lines kit
HKS Type S oil cooler kit
Samco radiator hose with water temp gauge fitting
Carisma S14 KA24DE to SR20DET swap heater hoses
Koyo Aluminum radiator
Nismo 1.3 bar radiator cap
Blitz SBC ID Spec R Boost Controller

Electronics:
Apex*i Power FC, Power Commander, and FC Datalogit
Greddy 52mm black boost gauge
Greddy 52mm black oil pressure gauge
Greddy 60mm white water temp gauge
Die Hard Platinum gel cell battery
Custom battery box relocation using 0 gauge wire
Rockford Fosgate 3 way splitter for engine bay positive wires
Rockford Fosgate battery ground
Rockford Fosgate Maxi fuse holder and 100 amp fuse for battery relocation kit

Suspension/Control:

Bushings/Mounts/Bracing:
Nismo motor and transmission mounts
Energy suspension front sway bar bushings
Trust front strut tower bar

Brakes:
Axxis ULT brake pads
Brembo blank rotors

Footwork:
KYB GR2 shocks
lowering springs
Muteki SR48 extended open ended lug nuts
Nismo 60mm extended lug studs
Nissan R32 GTS-T rear pumpkin and axles, 4.363:1 (stock 4.038:1)
Nissan R32 GTS-T VLSD - shimmed (performs like a 2 way)
Nissan 240sx SE wheels 16x6.5 +42 offset 5x114.3---not installed
Bridgestone Blizzak WS-60 205/55-16---not installed
Nissan 350z V1 Touring wheels 18x8 +30 offset 5x114.3
Exclaim UHP tires 225/40-18 front
Nitto Neogen 245/40-18 rear

Exterior:

Carbon fiber oem style hood
Nissan 200sx S14a front bumper
Nissan 200sx S14a fog lights
Nissan 200sx S14a turn signals
Mculloch HID kit 4300k

Electronics/Interior:

Audio:
Alpine CDA-9885 deck
Alpine SPR-17S Type R 6.5" component door speakers
Alpine SPR-17C Type R coaxial rear deck speakers
Alpine MRP-F550 4 channel Amp
Alpine MRP-M500 Mono Amp
Alpine SWR-1042D Type R 10" sub in vented box
Alpine iPod connector
Monster rca cables
Rockford Fosgate rca cables
Rockford Fosgate 1 farad capacitor

Driving refinements:
Nardi Torino Personal steering wheel (airbag removed)
Works Bell hub

Future Plans:
cage
5 point harnesses
NRG short hub, quick release and lock for steering wheel
s14 digital climate control
Kouki K or 270r rear spoiler
18x9 and 18x10 wheels with a lower offset
suspension rework, bushings, sway bars, coilovers


S14 Information:

Production: 2178 S14a's were exported to the USA in 1998
Body style 2-door coupe
Engine 2.0 L SR20DET (1998 cc)
Max Power 217 hp
Max Torque 203 lb·ft
Wheelbase 2525 mm (99.4 in)
Length 4498 mm (177.0 in)
Width 1727 mm (68.0 in)
Height 1288 mm (50.7 in)
Curb weight 1220kg (2689 lb)
Seating Capacity 4


The stock S14 SR20DET has a thrust bearing t28 pushing 11lbs of boost.
http://i80.photobucket.com/albums/j175/blackice00/random/2faf13cf0.jpg
http://i80.photobucket.com/albums/j175/blackice00/random/2fb113cf0.jpg
http://i80.photobucket.com/albums/j175/blackice00/random/2fb313cf0.jpg

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/IMG950073.jpg
http://i80.photobucket.com/albums/j175/blackice00/IMG955249.jpg
http://i80.photobucket.com/albums/j175/blackice00/IMG956807.jpg
http://i80.photobucket.com/albums/j175/blackice00/IMG_0363.jpg

[TiMoN]

car's sick!! welcome to the forum. good to see another nissan on here.

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/random/DSC01958.jpg

[blackice]

car's sick!! welcome to the forum. good to see another nissan on here.

thanks man

[RXSE7EN]

That is a fucking BITCHIN car dude.


I love the S14's so much.

[justin]

lets swap it!!!!!! HURRY!!!!

[RXSE7EN]

RB?
JZ?
13B?
SBC? (Small Block Chevy)


I can help too! haha.

[Sir Kyle]

Love the car man.

[gotrice93]

digging the car. have always been a big fan of the 240. they can be so expensive to buy. but i like how clean urs is

[blackice]

yeah.....mine was definitely a good chunk of change lol.
here are a few phone pics from the blown hg and pulling of the ka24de/tranny. thanks to marc's help it went decently fast but the obd2 head/intake manifold is a total pos, wires, water and vac lines everywhere. decided to say screw the ka after that and when the end of my intake cam decided to fall off after carefully pulling it and setting it down, bad casting i guess woohoo.

http://i80.photobucket.com/albums/j175/blackice00/Mobile%20Uploads/0515080424.jpg
http://i80.photobucket.com/albums/j175/blackice00/Mobile%20Uploads/0515080423a.jpg
http://i80.photobucket.com/albums/j175/blackice00/Mobile%20Uploads/0515080423.jpg

[blackice]

as it sits now, and yes the lip is off in the trunk, fiberglass and costco speed humps don't go well together. can't wait to pull that bumper and get a stock jdm kouki one to go with the fogs i already snagged. :razz:

http://i80.photobucket.com/albums/j175/blackice00/Mobile%20Uploads/1127081415.jpg
http://i80.photobucket.com/albums/j175/blackice00/Mobile%20Uploads/1127081414b.jpg
http://i80.photobucket.com/albums/j175/blackice00/Mobile%20Uploads/1127081414a.jpg
http://i80.photobucket.com/albums/j175/blackice00/Mobile%20Uploads/1127081414.jpg
http://i80.photobucket.com/albums/j175/blackice00/Mobile%20Uploads/1127081413a.jpg
http://i80.photobucket.com/albums/j175/blackice00/Mobile%20Uploads/1127081413.jpg

[blackice]

a few more old pictures i found...

http://i80.photobucket.com/albums/j175/blackice00/240sx/1-13-08meet5.jpg
http://i80.photobucket.com/albums/j175/blackice00/240sx/IMG_0411.jpg

[Backwoodz Tuner]

Daamn Sweet ride, clean as fuck. I've always liked the mean eye headlights on them 240's. Also love the color, looks good man !!

[Ty]

Cory, your 240 is really only like a 120. Until you get a new engine! Hahahaha.

Seriously though. Get some scratch together and let's SR that thing or something. Or make the jump to the Subaru world! RWD in the snow = FAIL

[Ayu4ever]

flippin sweet dude

[TatMatt]

Bummer . Man Cory get your ass in gear Spring is comming fast

[SMG]

KAD-T!

i've always wanted one.
SR's are too trendy.
plus KA's are a dime a dozen.

[TatMatt]

Good point I would love the bigger displacement of the KA plus the longer stroke will give you more torque with is better for kicking it sideways
That is why I love the 7m the thing is a torque monster. If there is even a little bit of moisture on the road I have no traction

[Domesticated]

ditto, i miss my old 5m. it was just the ge but it was ballsy for a 2.8 with 200k

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/240sx/IMG_0414.jpg
another one hahaha, blinked

[slice636]

sick car... if you are looking for parts go to Up Garage in Tacoma and talk to Doug... He knows his shit

[supeRB~GP]

http://i80.photobucket.com/albums/j175/blackice00/240sx/IMG_0414.jpg
another one hahaha, blinked



WOW....how the hell did you put a smily on your front wheel??? :cool::cool:

LOL

[blackice]

LOL never noticed that

[blackice]

Just got through ordering an s14 front clip today (includes a few choice upgrades) along with an s14 vlsd. Nismo mount kit, Bosch 040 fuel pump, Greddy boost and oil pressure gauges also ordered. :cornut:

[Backwoodz Tuner]

Hell yeah man, that's always a good feeling? So how long till christmas??

[blackice]

should take around three to four weeks to be ready for me to grab, no more than six. the container is shipping out of osaka.

[erik]

Just got through ordering an s14 front clip today (includes a few choice upgrades) along with an s14 vlsd. Nismo mount kit, Bosch 040 fuel pump, Greddy boost and oil pressure gauges also ordered. :cornut:

Sounds expensive. :yikes!:

[Backwoodz Tuner]

That ain't too long . I hate waiting for parts. But when they come it's like ,"MERRY CHRISTMAS 2 ME!" Well that's how I feel. :-D

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/DSC07483.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07488.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07489.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07495.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07497.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07498.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07499.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07500.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07501.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07502.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07503.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07504.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07505.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07506.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSC07507.jpg

[Domesticated]

wow awsome score man!

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07027.jpg
http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07026.jpg
http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07025.jpg
http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07024.jpg
http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07023.jpg
http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07020.jpg
http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07019.jpg
http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07014.jpg
http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07013.jpg
http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07012.jpg
http://i80.photobucket.com/albums/j175/blackice00/s14%20clip/DSC07008.jpg

[blackice]

clips on the boat this weekend, expecting it the week of august 9th woot

[justin]

Dude that's awesome! I'm glad to hear you'll have your car up soon.

[Brian]

don't really know much about Nissan's........is that a SR20DET?

[blackice]

don't really know much about Nissan's........is that a SR20DET?

correct, s14 sr20det with vct vs an s13 sr20det without

[Brian]

what is vct?

[blackice]

variable cam timing. can advance and retard up to 20* of timing ftw.

[509nestor]

hey is your front clips just for motor or will it come wit body parts cus if it does i need some for my 95 240sx

[blackice]

probably getting the bumper, fenders, and hood with the clip. i'll definitely keep you in mind and let you know when it arrives man.

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/DSCN0211.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0212.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0213.jpg

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/DSCN0216.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0217.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0219.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0221.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0222.jpg

couldn't stand it, got home at around 11:30pm after getting the tires mounted earlier today and had to throw em on in the dark :cornut:

[MetaEnder]

Tires look good dude. I love getting new tires, all the grip!

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/DSCN0224-1.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0225.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0226-2.jpg

Getting the car ready for the swap.

http://eddihughes.nissanpacific.com/corys-s14-front-clip-from-nw360performance/

[justin]

Get your shit running. Stop slacking. It's been two whole days!!

[blackice]

My current pile of boxes, jdm Nissan waterpump and thermostat, CARisma s14 sr20det conversion heater hoses, bosch 040 fuel pump (pwns the walbro 255), greddy 52mm boost gauge, and my set of Nismo motor and tranny mounts

http://i80.photobucket.com/albums/j175/blackice00/DSCN0273.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0272.jpg
Camber much? LOL
http://i80.photobucket.com/albums/j175/blackice00/DSCN0271.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0270.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0269.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0268.jpg
Test fit of the jdm s14 bumper, looks much better imo

[blackice]

More parts purchased, Greddy hot pipe/flange, and Greddy RZ Limited Edition bov :yesnod:

[justin]

Buy my boost controller

[blackice]

The Greddy RZ bov and flange showed up today. Talked to Eric down at UP Garage and he already has a harness ready to go woot! should be up and running next weekend or shortly after :cornut:

[justin]

SWEET, let me know if you need any help Cory. I don't mind staying sober to get a car done.

BTW, BUY MY BOOST CONTROLLER!!!!!!!!

[blackice]

Changed my mind on the rear diff, picking up an r32 pumpkin with a 2 way clutch type instead of the s14 1.5 way. The axles on the r32 are a bit thicker and has 4.3:1 ratio vs 4.083:1. More tq down low works for me, top end highway runs are meh lol

[erik]

Those wheels/tires make your car look lifted... or is it the pictures? Guess it doesn't matter, it will be hot.

[blackice]

probably the fact that its missing the driveshaft/tranny/engine LOL

[blackice]

Greddy hot pipe showed up today, now i'm just waiting for Eric down at U.P. Garage to finish my harness. Looks like I may be pulling the engine out of the clip tomorrow night for prep of the install on sunday. :yesnod:

[509nestor]

hey how much are u willing to sell your stock tranny i need one i fucked mine up.

[blackice]

Engine and tranny are out of the clip as of late last night/early this morning. radiator and everything look brand new lol.

i don't have the stock tranny any more, sold it last year with my ka block and head. also if you need zenki body parts jerry has a stack of them at 360performance up in bellingham.

[blackice]

Finally updated the mods list on the first page. Hopefully going to get this thing running by next weekend. Should have some pictures later. :yesnod:

[justin]

Sweet dude!! I can't wait to get a ride in it.

[Ty]

Deeeeetails.

[justin]

Did you ever figure out what turbo they were running?? Injectors??

[blackice]

stock s14 k's turbo with upgraded lines, pretty sure they are 555cc nismo injectors

[blackice]

engine is in with the harness, still have some things to finish up...tomorrow hopefully. pulled the tranny off also and it has a 6 puck clutch in there with a lightened flywheel and they are clean as hell. they looked new. glad i didn't buy new ones now lol

[Brian]

gotta love free goodies.

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/0923090714.jpg
http://i80.photobucket.com/albums/j175/blackice00/0923090714a.jpg
http://i80.photobucket.com/albums/j175/blackice00/0923090715.jpg
sorry for the phone pics, got some wiring left to do, and trimming of the bumper to fit over the intercooler lol

[SW-21turbo]

Dang, you got far. Great job!

[Domesticated]

yea no kiddin, are you sure your a nwtuner member? were known to be lazy and never even get around to the little things. great work man, vids asap

[erik]

You should probably get it running Cory... and I should get vtec... lolz!

[blackice]

LOL, and here I was thinking you had vtec this whole time Erik. I'm heading up to the shop in an hour or so to try to finish things up. I'll try to snap some better pics with the camera. Found out the radiator is a koyo also.

[blackice]

it runs and its pretty quick for a fairly stock setup. ill have to make someone ride along for video and snag some daylight pics. picking it up tomorrow and grabbing tabs and insurance again LOL.

[blackice]

http://i80.photobucket.com/albums/j175/blackice00/DSCN0309.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0310.jpg
bumper is on, rattle canned it real fast til i can afford a full body touchup and detail job.

[erik]

How about a video of you drifting some sweet NW roads?

[JetBlack]

yea no kiddin, are you sure your a nwtuner member? were known to be lazy and never even get around to the little things. great work man, vids asap

And don't forget the drinking.

[S14]

wait a minute are you on the west side? maybe thats why i havent seen this car.... well looks good. heres mine if you need and parts i got a few.

http://i64.photobucket.com/albums/h170/Supra989/SEX%2014/DSC03271.jpg

http://i64.photobucket.com/albums/h170/Supra989/SEX%2014/DSC03275.jpg

http://i64.photobucket.com/albums/h170/Supra989/SEX%2014/DSC03272.jpg

http://i64.photobucket.com/albums/h170/Supra989/DSC03254.jpg

[blackice]

yep west side. went and ordered a new rear pinion seal for the skyline diff today, its leaking a little bit. got a quote on blizzaks the other day for the stock wheels. those tires are freaking soft LOL.

[97lsteg]

wow that looks pretty pro man. Props!

[blackice]

moarrr
http://i80.photobucket.com/albums/j175/blackice00/DSCN0315.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0317.jpg
http://i80.photobucket.com/albums/j175/blackice00/DSCN0318.jpg

[blackice]

got the bov recirc'ed and a hallman pro mbc installed. new mishimoto starter is on the way along with a 1.3 bar nismo radiator cap :yesnod:

[blackice]

Blizzak ws-60's are mounted on my stock wheels woot, this thing's fun in the cold now lol. hoping to snag a greddy profec b spec 2 after christmas from a buddy. anyone interested in my hallman pro mbc?

[blackice]

New nitto neogen 245/40/18 tires going on the rear. Car is now aligned and I have a new 500w mono amp on the way for the sub.

[justin]

Now that your interior is back together let's
get some new shots of it.

[blackice]

reposting the pics from ty's detail thread http://www.nwtuner.com/forum/showthread.php?t=3338

http://lh6.ggpht.com/_1mwQxjaOShQ/S67flBJDIeI/AAAAAAAAB5Y/lz83Jnlj_AQ/s1024/DSC_4215.JPG
http://lh6.ggpht.com/_1mwQxjaOShQ/S67flmp5SdI/AAAAAAAAB5g/LF5bhV5Uyxc/s1024/DSC_4217.JPG
http://lh5.ggpht.com/_1mwQxjaOShQ/S67foOqGnBI/AAAAAAAAB54/5k_gCVqnaso/s1024/DSC_4223.JPG
http://lh5.ggpht.com/_1mwQxjaOShQ/S67fpTHBhgI/AAAAAAAAB6I/qsO6n4U73gc/s1024/DSC_4227.JPG
http://lh6.ggpht.com/_1mwQxjaOShQ/S67fqbYundI/AAAAAAAAB6U/fOXfskFVY6w/s1024/DSC_4230.JPG
http://lh4.ggpht.com/_1mwQxjaOShQ/S67frUgAJWI/AAAAAAAAB6g/ynYITV9aHs0/s1024/DSC_4233.JPG
http://lh4.ggpht.com/_1mwQxjaOShQ/S67fuGeRRsI/AAAAAAAAB7I/fhoE1EvrLgY/s1024/DSC_4242.JPG

[blackice]

there have been a few changes with the car since i checked the thread last. after ty's detail job i threw the nitto tires on the rear of the car and got a full alignment. my buddy in mt vernon that did the alignment also has an sr20'd 240 and said all of the 240sx he has had come in have had toe issues. after it was aligned the car handles way better lol.

got my amps and sub back in the car along with the cd deck. most of the interior is in and the gauges are all wired up.

lately the car started missing so i have been going through as i have time and money to try to find the issue. coil packs and ignitor look ok using a multimeter. went ahead and replaced the fuel injector seals and water temp sensor with no change. cleaned the iacv also and tried to get timing adjusted. was having trouble getting the idle below 1k so i suspect a vac leak. going to be doing all the intake manifold gaskets next. gotta hate cars sometimes :incazzato:

[blackice]

So after a long time of being in storage I drove the car down to U.P. Garage for a "break fix" session. Discussed the parts I had thrown in already to fix the missing problem I had awhile back. They ended up finding out cylinders 3-4 were leaking antifreeze from the headgasket with a badass fiber optic camera. Got video of the combustion chamber while it is running and a little drip drip under load lol.

Had a bit of pre-detonation damage on the pistons when inspected with the head on but was much less than expected when they pulled it. Just some carbon buildup and antifreeze residue that made it look rough.

New arp head studs and cosworth headgasket are now replacing the blown hks gasket and stock studs. They also threw in a new exhaust manifold gasket since it had a small leak and an intake manifold gasket for good measure.

Also the car is going on the dyno for tuning before I get it back. Bought a Nistune ecu awhile back and have had it sitting and waiting for the right time to do it. Going for a pretty safe tune but depending on power gain falloffs it may run up to 19 psi when tuned. Also had them throw on a new cat to replace my skyline test pipe since that is one of their dyno requirements. Hoping for more than my 18mpg I was originally getting too haha.

[blackice]

So got the headgasket replaced. The shop asked me about doing the clutch (the pedal was riding really high) while the car was there so I ordered one of the OS Giken Super Single clutches with the aluminum cover and a new Nismo clutch pivot ball. Should be good for around 400wtq

Sexy :mooner:
http://www.osgiken.net/products/images/racingclutch/supersingle/supersingle.jpg

[blackice]

So my car is finally on the road again. After my headgasket replacement it was thrown on the dyno for a tune. The ecu I had ended up having a faulty install of the Nistune board and my cas doesn't like sitting in the stock position.

Basically this caused it to advance timing up to around 30 degrees on the first speed dyno run and popped 3 piston's ring lands. The guys at UP Garage thought they had done something wrong with the tuning and ended up donating 3 pistons to my engine (awesome guys btw) and did a full teardown of my engine to figure out what the problem was.

Once the ecu problem was figured out they gave me a good deal on the labor to get everything back together. I decided to replace the Nistune and I was able to source a full Power FC kit including the Power Commander and and FC Datalogit from a cool guy I met from the Northwest Nissans forum.

Got everything buttoned back up with the new clutch and have been running 15psi for the past little while. The clutch master seals decided to stop holding pressure so I had that replaced and had the car thrown on the dyno for some more boost. Now it is sitting at around 18psi and very stable. For a stock turbo it is pretty quick.

I'm going to be picking up a full z32 caliper set in the near future along with some spl tension rods, outer tie rod ends and some z33 inner tie rods.

I highly recommend UP Garage especially after my car detonated because of the bad ecu. Their help and willingness to work with me to get it fixed and going again were great. Definitely going to be taking it back down there in the near future for some other work. :cornut:

http://i80.photobucket.com/albums/j175/blackice00/240sx/Picture19.jpg
http://i80.photobucket.com/albums/j175/blackice00/240sx/Picture20.jpg

[MetaEnder]

Nice! Glad to hear it's still on the road. I love 240's and yours is fantastic.

[blackice]

Another update, SPL tension rods, SPL Outer tie rod ends, and Tein Z33 inner tie rods arrive tomorrow. Also put the car in winter mode. Blizzak tires are win. Quick snaps from the parking garage and the NW Toy Run.

http://i80.photobucket.com/albums/j175/blackice00/240sx/383665_10150395027546954_690936953_8888963_1519395 712_n.jpg
http://i80.photobucket.com/albums/j175/blackice00/240sx/308995_10150376879886954_690936953_8834886_1547973 430_n.jpg